How to Setup Wavlink AC 3200 WiFi Router?
It might look hard to set up a new WiFi router, but don’t worry. We’ll teach you how to easily set up Wavlink AC3200 WiFi Router in this guide. After you follow these easy steps, your home will be connected right away. Let’s start:
What You Need To Get Started
Make sure you have these things before you start setting up:
- A router from Wavlink AC 3200
- A computer that works
- An Ethernet connection, which most routers come with
- A power plug
- A computer, phone, or tablet
Steps to Setup Wavlink AC 3200 WiFi Router
Step 1: Open the box and connect
- Take your Wavlink AC 3200 router out of the box and put it close to your modem.
- Connect the power charger to the wall to the router.
- Connect the modem to the WAN port of the Wavlink router with the Ethernet cord.
- Wait for the router’s power and internet lights to come on. It takes about one to two minutes.
Step 2: Join the router’s Wi-Fi network.
Now, do these things on your phone, tablet, or computer:
- Find the WiFi options on your phone or tablet.
- Find a network name that starts with “Wavlink,” like “Wavlink_5G” or “Wavlink_2.4G.”
Hook up to the web. You can find the default WiFi password in the instructions or on the bottom of the router.
Step 3: Go to the Browser
You can get to the setup page once you’re connected to the Wavlink WiFi:
- Open a computer browser, like Safari or Chrome.
- If you want to use 192.168.10.1, type it in the address bar and press Enter.
After that you will go to the login page, here enter default login credentials and complete Wavlink setup.
Step 4: Log into Setup Page
- You will be asked to log in on the setup page.
- The account and password that come with most websites are “admin.”
- Fill out the form and click “Login.
You can start setting up your Wavlink AC 3200 router once you’re logged in.
Step 5: Select the mode of operation
Router Mode, Repeater Mode, Access Point Mode, and WISP Mode are some of the different modes that the Wavlink router can be used in. Router Mode is the best choice for most home users.
- Pick “Router Mode” and click “Next.”
- The system might figure out what kind of internet link you have on its own.
- If not, pick the type your internet service gives you (DHCP, PPPoE, or Static IP)
- Type in any information asked for, such as your username and password (for PPPoE)
- To go on, click “Next.”
Step 6: Set WiFi Name and Password
Now it’s time to personalize your WiFi network:
- Enter a name for your WiFi in the SSID field. For example: “MyHomeWiFi”.
- Set a strong WiFi password (at least 8 characters).
- You can do this for both 2.4GHz and 5GHz networks.
- Click “Apply” or “Save” when done. The router will restart, and your device may disconnect for a moment.
Step 7: Reconnect and Test
- After the router restarts, go back to your device’s WiFi settings.
- Connect to the new WiFi network name you created.
- Enter the new password.4. Open a browser and check if you can access the internet.
- If ap.setup doesn’t load, use 192.168.10.1 instead.
- Reset the router by holding the reset button for 10 seconds if you make a mistake.
- Make sure your modem is working and cables are connected properly.
- If internet still doesn’t work, try rebooting both the modem and router.
If everything is working, your Wavlink setup is complete!
Troubleshooting Tips
Last Thoughts
Setting up the Wavlink AC 3200 router is simple if you follow these steps. You don’t need to be tech-savvy just connect the cables, log in to ap.setup, and configure your WiFi. Once done, you’ll enjoy fast and stable internet across your home.
FAQs
Should ap.setup not load, use the IP address 192.168.10.1 in your browser’s address bar. Your device should also be linked to the Wavlink WiFi network.
Press and hold the restart button for roughly ten seconds using a pin or paperclip to restart your router. Typically, the button is located on the rear of the router. The router will start up again and return to the settings it had when it was first manufactured.